Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - AylmerFreerider

Pages: 1 2 3 [4] 5 6
46
Super 8 / Re: 2018 Super8 50x derestricting CDI?!!!
« on: August 22, 2018, 12:17:01 AM »
I have a 2015 4 stroke

There was a purple wire (purple w/ red stripe} that I just removed from the wire harness.  no more RPM restriction

47
Agility 50 / Re: Kymco Agiliy City 16+ 50i slooow
« on: August 04, 2018, 07:30:09 PM »
i have a 4t super 8.  the bigger jet works wonders.  i was amazed at the difference going from an 80 to an 82 made.

tell the dealer to change and it will help you. 

48
Super 8 / Re: 2016 Kymco Super 8 50x 4 Stroke Derestricting Problems
« on: May 21, 2018, 12:26:45 AM »
There is purple wire or wire with a purple stripe.

Don't hut it though.  Just remove it from the wire harness so you can install later on if you want.
I just covered it with electrical tape

49
Super 8 / Re: Cdi Still Restricted!
« on: May 21, 2018, 12:24:05 AM »
You want more speed put in heavier weights.  Especially with the 72cc upgrade kit.  6.5 or even 7 gram will help you increase your speed.

50
Technical | How To / Re: Kymco Super 8 50CC 4stroke modification (need for speed)
« on: May 21, 2018, 12:21:59 AM »
don't cut the wire just slip it out of the harness and cover it with electrical tape.
It was the purple one.

I have the the 2015 version and the issue is that it is a 4 stroke.  2 strokes have way more power.

There is a washer in the manifold that can be removed as well.  It will allow more fuel to pass.

The only other option for more speed and a 70cc upgrade kit and new rear gear.

Hope this helps.  I am about to do the 70cc kit on mine.


51
Technical | How To / Re: 2015 Super 8 50R 4T Cylinder Kit Upgrade
« on: May 05, 2018, 11:35:39 PM »
Bueller..........Bueller..........Bueller

52
Technical | How To / 2015 Super 8 50R 4T Cylinder Kit Upgrade
« on: May 04, 2018, 12:27:49 PM »
Just looking for any tips and tricks for this.  I have ordered and am hoping to install in the next week.

Purchased the folowing

https://www.scootertuning.ca/en/cylinders-70-90cc/850002-cylinder-kit-72cc-gy6-50cc-139qmb-qma.html

With the upgrade main jet and these little air filter box mods

https://www.scootertuning.ca/en/air-filters-airbox/6117-air-filter-supplement-uni.html?search_query=air&results=683

Not 100% sure what to expect but excited to see the results

53
People 50 / Re: 72CC Kit in my People 50S 4T!
« on: March 27, 2018, 07:14:27 PM »
I was hoping you could repost the pictures.  I am looking at doing the exact same thing to by engine in the next month.

54
Technical | How To / Re: Exhaust getting louder?
« on: September 17, 2017, 12:51:27 AM »
Hey Stig,

Yes the sound is coming form the front.  I didn't tighten everything till all screws and nuts were in place just like the instructions said.  Will try and take a pic with my phone and see what I can find. Just wondering if maybe I should use a gasket, plus some type of rubberized gasket in a tube to double things up.

55
Technical | How To / Exhaust getting louder?
« on: September 15, 2017, 12:16:29 AM »
Hi All,

I installed the Technigas Silent Pro on the 2015 Kymco Super 8 50R and it seemed ok at first but then I noticed that it seems to be getting louder and louder at the front of my scooter.  I did use a new gasket when installing as well and everything is tight.  Any ideas why it might be getting louder?  What else can I do?

Thanks

56
Agility 50 / Re: CDI Restriction
« on: September 06, 2017, 06:47:50 PM »
dude...

No need to hack the box.  Just remove the purple wire from the wire harness and cover with electrical tape.  So you can put it back if you ever get a unrestricted CDI

57
Technical | How To / Re: 1000rpm Vs 1500rpm Spring
« on: September 04, 2017, 03:14:07 PM »
Also should I be changing the little springs to as well at the same time?

58
Technical | How To / 1000rpm Vs 1500rpm Spring
« on: September 03, 2017, 09:18:14 PM »
Getting ready to upgrade my spring and am trying to decipher which one to go with on my 2015 Kymco Super 8 50R (4 stroke)

My set up is as follows:

Piolini High Speed Variator (6.9 gram rollers)
Technigas Silent Pro Exhaust

The Polini says to go with a 15% stiffer spring but the issue is I do not know what the OEM spring is.

I keep seeing go with the red(1500) or go with the white(1000).


Any advice would be greatly appreciated

59
Super 8 / Re: More power / uphill ??
« on: August 29, 2017, 05:32:06 PM »
You will be fine after the higher octane gets in there.  We have Super (91) and Ultra (94) here in Canada.  I use the Ultra whenever available. 

60
Super 8 / Re: Ordering parts
« on: August 29, 2017, 01:09:30 PM »
Typically you can look a the Agility 4T for the same parts.  The newer Super 8's are based off this model.

Pages: 1 2 3 [4] 5 6