Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - DaxFX

Pages: [1]
1
People GT 300i / Re: Rattling from clutch or variator.
« on: August 01, 2018, 02:17:13 AM »
Hey guys sorry my late reply. Im thinking to service my CVT this weekend. What should i do?, i will sand the clutch pads, check rollers, belt, spring etc what should i look for?

Also I was looking into upgrade for something smother what you recomend to me goys ? I will start with some 14g Dr. pulley.

Im happy with stock setup performance. I can add just a bit more faster response.

What good clutch and variator are out there for the Gt300 ?
 


Sent from my iPhone using Tapatalk

2
People GT 300i / Rattling from clutch or variator.
« on: July 18, 2018, 02:48:14 AM »
Hi guys. My people gt300i is doing a wierd rattling and looks like is coming from inside the belt-clutch-variator housing.

The sound is like a rattling noise and only happends when i hit full throtle (or almost full) at a 0-5 mph only at that speed.  If i ride normal doesnt do the noise.

I went to the dealer and they told me is the  clutch and all 300gti  do the sane after a little wile. They told me not to buy new clutch because it will do the same after a little wile. They told me my solution is going with aftermarket clutch like a malossi.  but my scoot have only 1,500 miles on it.

Is like the noise happends wile clutch is not fully engage or like the variator weights is rattling around. After i gain some speed (or clutch fully engaged) i can hit full throtle and all good.

Any recomendation ? Thanks


Sent from my iPhone using Tapatalk

3
People GT 300i / Throttle grip free play.
« on: September 02, 2017, 02:56:31 PM »
Hi guys, i have too much play in my throttle grip. I want to adjust a little bit, in the service manual are two options. Adjust in carburador end and adjust in the grip for minor adjustment. But the grip side doesnt tell to much, looks like it is a push-pull wire system any idea on how to adjust them? Any 1 had done this?

4
People GT 300i / Re: Top box trunk rattle. How to fix?
« on: August 30, 2017, 06:28:19 PM »
Hello DaxFx and welcome to best scooter forum on the web.When I've had this happen to me, I backed off on the mounting bolts and cut some pieces from a 1/16th inch piece of black rubber and slid them up under the rear of the top box and then re tightened the bolts. Worked for me. You might even cut out four ribber washers and place them on all for bolts between the bottom of the box and the mounting surface. Hope this helps.
Thanks. I will try this and let you know.

5
People GT 300i / Top box trunk rattle. How to fix?
« on: August 26, 2017, 03:51:51 PM »
Hi guys, I hate the rattle in the top box i was thinking on put some foam tape but not sure what to do. What you guys are doing to get rid of the rattle? What size of tape will fit in the channels ?

Thanks!

6
People GT 300i / Re: Turn signals and headlamp
« on: May 23, 2017, 12:55:27 PM »
https://www.ebay.com/itm/252489002905

This are day & night diference.

7
People GT 300i / Turn signals and headlamp
« on: April 09, 2017, 05:37:37 AM »
I just upgraded my new GTi300 with Euro turn signal en H4 led. my local Dealer were i purchased my GTi300 did the turnsignal mod and put on the new h4 led, Im very satisfied with thr result, at the moment the H4 led was out of stock on the dealer so I ordered from ebay en bring the led to them, they remove the usa turn signals and activate the original ones, its a cleaner look now, just want to share, and maybe new people gti300 owner wants the turn signal mod can ask their dealer to do it ! i was charged very cheap for that. it was worth every penny !!!!

8
People GT 300i / New GTI owner with few question.
« on: March 28, 2017, 12:40:49 AM »
Hi guys. I got a new 2015 GTI las week and i have few questions.

1- yellowish headlight bulb aahhh ahhhhh i need a h4 led asap so my question is. Is there any guide on how to get to the bulb, the manual is very dumb on taking apart the plastics. can i fit a h4 led with heatsink or fan , do they have enough space?

2- activate euro turnsignal. How can i get to the front turnsignal.  Are the bulb socket already in place? Any guide on how to do the euro blinker back to work.

I have try to get into both bulbs but looks like no matter how many screws i take out non of the plastics will came out

3- top box rattle (solved) no more top box in my bike.

3- Handlebar  my handlebar plastic rattles a little bit not as bad as the top box but still rattle

Why kymco still using the worst plastic ever found for a scooter. It is a shame that a good reliable bike came with this cheepy feel plastics

Do you guys get rattle and squeaking noise from handlebar?

Pages: [1]