Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Berzerker1965

Pages: 1 2 3 [4]
46
Like 50 2T / Re: Just bought a new 2013 Like 50
« on: June 28, 2014, 02:06:20 PM »
Great idea Zombie, I read the thread about that guy who shattered his rings after he cleaned out the carbon build up. If he ported and polished he would have avoided that. Better to do it right the first time than to have a catastrophic failure. Those pictures were ugly.

47
Like 50 2T / Re: Just bought a new 2013 Like 50
« on: June 28, 2014, 12:18:06 AM »
Just tried calling Scooter Parts International they are closed will try again Monday.

48
Like 50 2T / Re: Just bought a new 2013 Like 50
« on: June 27, 2014, 07:23:17 PM »
Think I'm gonna use Dr Pulley Sliders instead of rollers.

49
Like 50 2T / Re: Just bought a new 2013 Like 50
« on: June 27, 2014, 05:06:22 PM »
I've read it's better to run rich while breaking in the kit & also to add 1 oz. oil to gas to ensure it runs rich. I plan on adjusting the jets to optimum after the breaking period.

I plan on ordering parts this week-end and will post on my final part list.

Are there any special tools I will need besides a torque wrench(which I have) and the usual metric socket & wrench sets? I don't have access to a vise or work table. Just a plastic yard
table on my patio.   

Thanks again!

50
Like 50 2T / Re: Just bought a new 2013 Like 50
« on: June 26, 2014, 04:19:20 AM »
Sorry I haven't posted earlier, my birthday was Saturday when I bought the scooter, my plus one ,Rebecca, has been working until yesterday so the past two nights have been just for us. Gonna have to read,think and reply after some well deserved rest.

Thanks again!

51
Like 50 2T / Re: Just bought a new 2013 Like 50
« on: June 24, 2014, 06:00:20 PM »
Thanks for all the informion you guys are great. Helping me set up my scooter and saving me money?
I am speachless.

Here is the planned set up so far.

70 cc BBK kit
Dell Orta PHBG 19mm AS carb
?? pilot jet
96 main jet
Polini variator
Polini clutch kit
7.5 rollers
2000rpm contra spring
Stock exhaust pipe

I'm looking for hill climbing/ wind fighting power more than speed. Reliability is a factor as well.
I read the 70 BBK thread last week and I believe that it said a #96 main jet was good. Any suggestions
on the jetting would be helpful. I picked the 7.5 rollers after reading scooter Mavin's thread.

I am about 210lbs and would like a quick take off speed. I'm using the scooter for commuting, so a 35-40 mph cruising speed would be optimal.

Once again thank you. You guys are a huge help.








52
Like 50 2T / Re: Just bought a new 2013 Like 50
« on: June 24, 2014, 01:39:03 AM »
I've just broke 100 miles! Went out to get dinner, any excuse to ride. Lol. Quick question. Should I continue the break in and finish, before I mod or go ahead and mod it and start the break in anew? I'm replacing a lot of parts that require break in.

Once again l would like to say thank you.

53
Like 50 2T / Re: Just bought a new 2013 Like 50
« on: June 24, 2014, 12:42:29 AM »
Thanks about the tire pressure I'm about 210 & she's about 98lbs. I read your post about the exhaust. Not to sure if I want to go that far. If anything I will go with a new exhaust.

54
Like 50 2T / Just bought a new 2013 Like 50
« on: June 23, 2014, 01:35:48 AM »
Just bought my 2013 Like 50. Had a Honda CH80. The missing 30 cc is killing me. I ride with 2 people a lot and want to get a big bore kit. I've read all the posts here and learned tons. Thanks guys. Any way I'm breaking in the scooter now. 90 miles so far. Ride for 10 miles stop and let the engine cool and ride another 10 miles. I would like to the upgrade all at once. I'd like to keep the exhaust and not pre-mix oil if possible, I'm lazy. I figure big bore kit and new carberater. Change clutch spring to 1500, but open for suggestions on anything and everything. The scooter handles great any has plenty of room for my plus 1. Just looking for more power.

Pages: 1 2 3 [4]