1
Xciting 500 / Re: x500 wont start
« on: September 21, 2012, 08:55:40 AM »
OK, the mech said, that the shaft comp reduction is faulty. Pffff. It works like a clutch. Now i need a new one, great.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Xciting 500 / Re: how to tighten steering nut....
« on: July 04, 2012, 03:05:35 PM »
There is no way to tighten it without taking the front plascitcs off. I tried once. 
But doesnt matter, it takes 10minutes. One thing is necessary, not to tighten it too much!
But doesnt matter, it takes 10minutes. One thing is necessary, not to tighten it too much!
3
Xciting 500 / Re: x500 wont start
« on: July 03, 2012, 08:34:46 AM »
The BAS works fine, it gives the spark (when its wrong or stucked there is no spark). The coil is good too (i think), warm and hot engine doesnt matter, spark OK
The trouble must be deeper, or something stupid electricity (ignition timing for example). But the mech works so slowly...
The trouble must be deeper, or something stupid electricity (ignition timing for example). But the mech works so slowly...
4
Xciting 500 / Re: x500 wont start
« on: July 02, 2012, 04:26:52 PM »
Which unit, the BAS? The coil?
5
Xciting 500 / Re: x500 wont start
« on: July 02, 2012, 07:17:10 AM »
Hi!
Your problem is not the same.
From the beginning :-) I bought the scooter 5 month ago. After changed oil-brake fluid-filters, once it did not start. Everithing looked fine, but wont start. With my "original" mech we checked everithing, there was no spark.
We changed the coil, nothing. The solution was the magnet sensor in the BAS. After he solded the wrong part, it worked fine :-) Happy!!!
But.
After the repair once in the morning it did not start, again. Spark was OK, but the same as now. Next morning it started, nothing wrong. Ahhh. OK, at last we were on tour, but when we stopped for 10 minutes, the bike did not start. And here am I now, strange situation, for me :-)
Your problem is not the same.
From the beginning :-) I bought the scooter 5 month ago. After changed oil-brake fluid-filters, once it did not start. Everithing looked fine, but wont start. With my "original" mech we checked everithing, there was no spark.
We changed the coil, nothing. The solution was the magnet sensor in the BAS. After he solded the wrong part, it worked fine :-) Happy!!!But.
After the repair once in the morning it did not start, again. Spark was OK, but the same as now. Next morning it started, nothing wrong. Ahhh. OK, at last we were on tour, but when we stopped for 10 minutes, the bike did not start. And here am I now, strange situation, for me :-)
6
Xciting 500 / Re: x500 wont start
« on: June 30, 2012, 03:29:11 PM »
Diaphragm is good, moves easily, checked
I'VE a leonardo250 coil, looks the same as kymco.
The wrong time ignition could be possible, mech must check it i think.
I'VE a leonardo250 coil, looks the same as kymco.
The wrong time ignition could be possible, mech must check it i think.
7
Xciting 500 / Re: x500 wont start
« on: June 30, 2012, 01:21:27 PM »
Hi!
Your options are good, I've checked them already.
The side stand is OK
Kill switch and brake switch OK
Spark out OK (NGK CR8EIX, NGK CR8E), I dont know, how to check it when its in
AC OK, it pumps (as you said click click) gas (maybe too much)
I hope the compression is good, when the sp plug is out it pumped the mixture very fast and hard next to my finger, but mechanic should check it
At the end, the electricity. This is the worst, it can be a small problem, but to find it can be a nightmare. The COIL?? Good idea, gonna tell mech, but change it will be hard in my country. Which Kymco has the same coil?
Your options are good, I've checked them already.
The side stand is OK
Kill switch and brake switch OK
Spark out OK (NGK CR8EIX, NGK CR8E), I dont know, how to check it when its in
AC OK, it pumps (as you said click click) gas (maybe too much
)I hope the compression is good, when the sp plug is out it pumped the mixture very fast and hard next to my finger, but mechanic should check it
At the end, the electricity. This is the worst, it can be a small problem, but to find it can be a nightmare. The COIL?? Good idea, gonna tell mech, but change it will be hard in my country. Which Kymco has the same coil?
8
Xciting 500 / x500 wont start
« on: June 30, 2012, 07:37:42 AM »
Hi Everybody!
I'm new member and happy to find this forum. I live in Hungary and thats one of my problems, I hope you can help me.
So the situation. Xciting 500, 2005, carb, 28000km. And it won't start :-( The starter works (I've changed it a new one), spark OK, carb clean, valve clearence 0.1mm, AC OK.
Ignition problem?
Compression?
So, my new mechanic try to manage the problem, but I think its too complicated for him
I'm new member and happy to find this forum. I live in Hungary and thats one of my problems
, I hope you can help me.So the situation. Xciting 500, 2005, carb, 28000km. And it won't start :-( The starter works (I've changed it a new one), spark OK, carb clean, valve clearence 0.1mm, AC OK.
Ignition problem?
Compression?
So, my new mechanic try to manage the problem, but I think its too complicated for him
Pages: [1]