1
zx50 / Re: About to build! ZX 50
« on: September 02, 2011, 11:44:40 PM »
I found out!.. there was an air leak at the intake to the motor didn't seal good i guess.. got that fixed so I didnt't need the choke on anymore .. Thanks
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
zx50 / Re: NOOB ZX50 SITTING, WHERE TO START????
« on: September 02, 2011, 11:41:56 PM »
are you wanting to go all out? or just a few things here & der? !!
best thing about the ZX 50 is it has the same motor as the Honda Dio...! Alot of parts put there...!
best thing about the ZX 50 is it has the same motor as the Honda Dio...! Alot of parts put there...!
3
zx50 / Re: About to build! ZX 50
« on: August 31, 2011, 04:07:27 PM »
what do you me?...
anywho.. I did it today and got it all done in 5 hours she took a lil bit to get started....
only thing now is to tune it... It will only run with the choke on.. anyone help.. its a 28mm OKO not sure about the jet size!
anywho.. I did it today and got it all done in 5 hours she took a lil bit to get started....
only thing now is to tune it... It will only run with the choke on.. anyone help.. its a 28mm OKO not sure about the jet size!
4
Technical | How To / About to build ZX 50
« on: August 29, 2011, 08:44:39 PM »
About to build ZX 50!
Hello all, I posted once befor & got a lot of help Thanks!
anywho blow is a pic of all my parts I will be putting in tomorrow and just looking for any tips, like
step by step installing tips or how to's on the parts would be every helpful !!
I did it once befor on a ZX about 7 years ago but with all my older friends and they took most of the lead, I am
just a little worry about the bore kit itself and the clutch...
and if the carburetor is tuned or does it need to be set up on frist start up... and some pre-mixing for the gas doing the
brake in and aftermath! ...lol
and anything I may need to know or FYI's any & all is helpful.. will be glad to follow up will all of you once its done!
right now It is just about stock.. hitting 40-45MPH
I'm 5'8 and 248lbs. bigger guy
2002 Kymco ZX 50
A little info on the parts.
Dio 48mm Big Bore Kit,
28 OKO carburetor
Polini speed Pulley
Polini 2G clutch with blue springs
2k Dio spring
V8 free flow pipe
Racing CDI 5 pin
Polini wights 5.6g
about 700$ in parts all from Hawaii!
Hello all, I posted once befor & got a lot of help Thanks!
anywho blow is a pic of all my parts I will be putting in tomorrow and just looking for any tips, like
step by step installing tips or how to's on the parts would be every helpful !!
I did it once befor on a ZX about 7 years ago but with all my older friends and they took most of the lead, I am
just a little worry about the bore kit itself and the clutch...
and if the carburetor is tuned or does it need to be set up on frist start up... and some pre-mixing for the gas doing the
brake in and aftermath! ...lol
and anything I may need to know or FYI's any & all is helpful.. will be glad to follow up will all of you once its done!
right now It is just about stock.. hitting 40-45MPH
I'm 5'8 and 248lbs. bigger guy
2002 Kymco ZX 50
A little info on the parts.
Dio 48mm Big Bore Kit,
28 OKO carburetor
Polini speed Pulley
Polini 2G clutch with blue springs
2k Dio spring
V8 free flow pipe
Racing CDI 5 pin
Polini wights 5.6g
about 700$ in parts all from Hawaii!
5
zx50 / About to build! ZX 50
« on: August 29, 2011, 08:38:16 PM »
About to build ZX 50!
Hello all, I posted once befor & got a lot of help Thanks!
anywho blow is a pic of all my parts I will be putting in tomorrow and just looking for any tips, like
step by step installing tips or how to's on the parts would be every helpful !!
I did it once befor on a ZX about 7 years ago but with all my older friends and they took most of the lead, I am
just a little worry about the bore kit itself and the clutch...
and if the carburetor is tuned or does it need to be set up on frist start up... and some pre-mixing tips what rate should I use. for the gas doing the
brake in and aftermath! ...lol
and anything I may need to know or FYI's any & all is helpful.. will be glad to follow up will all of you once its done!
right now It is just about stock.. hitting 40-45MPH
I'm 5'8 and 248lbs. bigger guy
2002 Kymco Zx 50
A little info on the parts.
Dio 48mm Big Bore Kit,
28 OKO carburetor
Polini speed Pulley
Polini 2G clutch with blue springs
2k Dio spring
V8 free flow pipe
Racing CDI 5 pin
Polini wights 5.6g
about 700$ in parts all from Hawaii!
Hello all, I posted once befor & got a lot of help Thanks!
anywho blow is a pic of all my parts I will be putting in tomorrow and just looking for any tips, like
step by step installing tips or how to's on the parts would be every helpful !!
I did it once befor on a ZX about 7 years ago but with all my older friends and they took most of the lead, I am
just a little worry about the bore kit itself and the clutch...
and if the carburetor is tuned or does it need to be set up on frist start up... and some pre-mixing tips what rate should I use. for the gas doing the
brake in and aftermath! ...lol
and anything I may need to know or FYI's any & all is helpful.. will be glad to follow up will all of you once its done!
right now It is just about stock.. hitting 40-45MPH
I'm 5'8 and 248lbs. bigger guy
2002 Kymco Zx 50
A little info on the parts.
Dio 48mm Big Bore Kit,
28 OKO carburetor
Polini speed Pulley
Polini 2G clutch with blue springs
2k Dio spring
V8 free flow pipe
Racing CDI 5 pin
Polini wights 5.6g
about 700$ in parts all from Hawaii!
6
zx50 / Re: New ZX 50! help..
« on: August 14, 2011, 10:19:55 PM »
Yeh.. my 01 came like that too.. lol funny how they would do it and not do ti. Thanks!!
7
zx50 / New ZX 50! help..
« on: August 14, 2011, 07:50:27 PM »
Hello everyone ! I am new to this fourm! but am a Kymco owner ! and was befor...
I used to have a 2001 Kymco ZX 50 back in the day in Hawaii where I'm from. and I put parts of it.. bore, carb,pully.ect... evething A Dio had I had same type ! AF18e.
I had it for years ended up selling it.. anywho.. I moved to WA state 3 years ago and got a new ZX 50.. its a 2002 3,000MI on her.
and have all my parts from Hawaii in da mail
(about 800$ in parts ) 
and went outside today to go chnage the blinker lights from the stalk-type turn
signals and wire-up the integrated ones .. but They are FAKE on this 2002 or Its just this bike ... I did this to my 2001 years ago and the back turn
signals also... Why don't they could pre-wired anymore? I mean the hole is not even der
I'm upset.. taking the stalk-type one makes it look wayyy nicer any tips on how
to over come my prob? anythings helps.. or even a place to buy the wires! Thanks
Aloha
Mark !
I used to have a 2001 Kymco ZX 50 back in the day in Hawaii where I'm from. and I put parts of it.. bore, carb,pully.ect... evething A Dio had I had
same type ! AF18e.I had it for years ended up selling it.. anywho.. I moved to WA state 3 years ago and got a new ZX 50.. its a 2002 3,000MI on her.
and have all my parts from Hawaii in da mail
(about 800$ in parts ) and went outside today to go chnage the blinker lights from the stalk-type turn signals and wire-up the integrated ones .. but They are FAKE on this 2002 or Its just this bike ... I did this to my 2001 years ago and the back turn
signals also... Why don't they could pre-wired anymore? I mean the hole is not even der
I'm upset.. taking the stalk-type one makes it look wayyy nicer any tips on how to over come my prob? anythings helps.. or even a place to buy the wires! Thanks
Aloha
Mark !
Pages: [1]