1
Technical | How To / Re: Kymco G-Dink 50 CDI restricted
« on: July 19, 2025, 12:30:18 PM »
Okay, thank you for your response and I will take a look further on the forum.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Technical | How To / Kymco G-Dink 50 CDI restricted
« on: July 18, 2025, 08:36:43 AM »
Hi, I'm new to this forum so I hope I'm posting this in the right place, reposted because the other one wasn't right.
My scooter is a:
Kymco G-Dink form 2017 2 stroke
70CC polini
20mm carburetor
Vario form Malossi
White spring form Malossi
Tension springs red
Exhaust Tecnigas next-r
Everything works fine, but my CDI is limited to 8000rpm and my powerband is 8800rpm.
I looked for other CDI, but I have an 8 pin I couldn't find anything for my engine SF10R.
The only thing what I found was the Naraku NK390.35, but that is not suitable for engine.
I tried the Naraku CDI, but the scooter started with difficulty and cut out immediately and sometimes had a backfire.
Who can help me remove the limiter?
Or have ideas how I can fix this?
My scooter is a:
Kymco G-Dink form 2017 2 stroke
70CC polini
20mm carburetor
Vario form Malossi
White spring form Malossi
Tension springs red
Exhaust Tecnigas next-r
Everything works fine, but my CDI is limited to 8000rpm and my powerband is 8800rpm.
I looked for other CDI, but I have an 8 pin I couldn't find anything for my engine SF10R.
The only thing what I found was the Naraku NK390.35, but that is not suitable for engine.
I tried the Naraku CDI, but the scooter started with difficulty and cut out immediately and sometimes had a backfire.
Who can help me remove the limiter?
Or have ideas how I can fix this?
3
Technical | How To / Kymco G-Dink 50 CDI restricted
« on: July 16, 2025, 11:52:25 AM »
Hi, I'm new to this forum so I hope I'm posting this in the right place.
My scooter is a:
Kymco G-Dink form 2017 2 stroke
70CC polini
20mm carburetor
Vario form Malossi
White spring form Malossi
Tension springs red
Exhaust Tecnigas next-r
Everything works fine, but my CDI is limited to 8000rpm and my powerband is 8800rpm.
I looked for other CDI, but I have an 8 pin I couldn't find anything for my engine SF10R.
The only thing what I found was the Naraku NK390.35, but that is not suitable for engine.
I tried the Naraku CDI, but the scooter started with difficulty and cut out immediately and sometimes had a backfire.
Who can help me remove the limiter?
Or have ideas how I can fix this?
My scooter is a:
Kymco G-Dink form 2017 2 stroke
70CC polini
20mm carburetor
Vario form Malossi
White spring form Malossi
Tension springs red
Exhaust Tecnigas next-r
Everything works fine, but my CDI is limited to 8000rpm and my powerband is 8800rpm.
I looked for other CDI, but I have an 8 pin I couldn't find anything for my engine SF10R.
The only thing what I found was the Naraku NK390.35, but that is not suitable for engine.
I tried the Naraku CDI, but the scooter started with difficulty and cut out immediately and sometimes had a backfire.
Who can help me remove the limiter?
Or have ideas how I can fix this?
Pages: [1]