1
People s200 / Re: slow warm up
« on: July 16, 2016, 07:12:51 PM »
see my handlebar cover post for solution to slow warm up 
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
People s200 / Re: rear handlebar cover on 2008 People S 200
« on: July 16, 2016, 07:11:50 PM »
finally took scooter to local M/C repair shop and he fixed it and agreed that rear handlebar cover was a bear to get off. The slow warm up was a combination of bad fuel and cleaning the original carburetor thoroughly and resetting the jet screw. Advised to never use ethanol fuel if scooter is to sit long unused. Head light module tested bad but for $67cost of new one he saved me by bypassing the module and light now works fine. Turn signal was a loose connection and now the scooter runs like a new ride.I found a local supplier of ethanol free 89 octane and add stabil to every tankful. Since I now have a barely used complete carburetor I will sell for $100. contact me here. 
3
People s200 / Re: rear handlebar cover on 2008 People S 200
« on: July 02, 2016, 05:12:03 PM »
Thanks again Isahawk, I have followed all your directions and the illustrations in the Cyclopedia manual and still cannot get the cover over the bolt receivers that you describe in your reply. Not wanting to break the cover by forcing it I have turned it over to a repair shop. I am not at all sure it is the bulb for either the turn signal or the headlight as they both went dead after the carburetor replacement and both the front AND rear left TS went out. There is mention of a headlight control module and since the other issue (Auto Bystarter) are both electrical I suspect there is a global problem in the electrical system. I do appreciate your replies and will update forum if the cure is found. 
4
People s200 / rear handlebar cover on 2008 People S 200
« on: June 30, 2016, 12:56:27 AM »
I cannot get the handlebar cover off to service the headlight and turn signals. I had a post say to give a mighty pull after taking out all 6 screws and bolts which I did but to no avail. I don't want to break the cover and Kynco has not responded to my email request for help. Does anyone have a clue on this?
5
Technical | How To / Re: rear handlebar cover on 2008 People S 200
« on: June 29, 2016, 12:05:42 AM »
Thanks Iahawk, I will give that a try. I am always afraid of muscling on plastic parts for fear of breaking them and then big costs to replace them. Why would Kymco make it so hard to get to the headlight and instruments panel?
6
People s200 / slow warm up
« on: June 28, 2016, 09:31:11 PM »
I installed a new carburetor on my 2008 Peoples S 200 and put in a new spark plug. I was hoping to eliminate the very slow warm up time before the engine could take any throttle. Still have that problem. It seems like an electrical choke issue but since the carb was new I thought that would solve the problem. It did not! Engine will start instantly but won't take throttle for at least 10 minutes of idle time. Any suggestions?
7
Technical | How To / rear handlebar cover on 2008 People S 200
« on: June 04, 2016, 05:00:45 PM »
???I installed a new carburetor on my '08 Peoples S 200 and after re-installing the covers and starting up engine the headlight would not come on and right front turn signal has no voltage. I tried to take off the rear handlebar cover and with all tabs unfastened as per repair manual the windshield came off easily but the rear cover would not detach from frame. Any suggestions ?
8
People s200 / new carburetor and headlight goes out
« on: June 04, 2016, 01:41:05 PM »
I replaced the carburetor on my 2008 People S 200 and scooter runs fine but headlight won't come on. Tried to take off rear cover for headlight replacement but could not get it to come off. Any suggestions
Pages: [1]