121
Complete factory exhaust off a 2010 People 150. System was on scooter for 500 miles, and is in excellent condition. Includes Chrome
cover. $100.00
cover. $100.00
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
122
For Sale / 2010 People 150 (SOLD)
« on: October 16, 2012, 11:48:19 AM »
SOLD: 2010 People 150. Black & Tan. Topcase & Windshield. Custom (NHRC) exhaust. Bought new in June 2012. 2089KM. 75mpg. Top speed 58-60mph
Scooter is located in Syracuse, NY. New job=longer commute on interstate highways=bigger & faster scooter needed. Buying a People 300GTI in the
spring. Asking $1600.00
E-mail me at mrmikesdeuce@aol.com for any more details and pictures
Scooter is located in Syracuse, NY. New job=longer commute on interstate highways=bigger & faster scooter needed. Buying a People 300GTI in the
spring. Asking $1600.00
E-mail me at mrmikesdeuce@aol.com for any more details and pictures
123
People GT 300i / ABS???
« on: October 07, 2012, 05:42:48 PM »
I just bought a people 150 in June and love the scooter. Unfortunately my job site has changed, and now I commute about 15 miles a day on interstates. The 58-60 mph of my current scooter doesn't cut it. I have pretty much made up my mind to buy a People 300GTI, but I have seen articles about a 300GTI/ABS. Is this scooter available in the US, and what is the MSRP on it?
124
People GT 300i / Aftermarket parts
« on: September 30, 2012, 12:07:19 PM »
I just got my People 150 running great and then I saw the 2013 People GT300I. I want one. I know I won't want to leave it alone, so my question is about the availability of aftermarket parts. I would be looking for exhaust systems, variator rollers or sliders, and possibly a bigger contra spring. Are these performance parts available for this model?
125
General Discussion / New Picture
« on: September 16, 2012, 03:16:58 AM »
Just a question for the board moderator. I tried to update the picture on my profile, and now I can"t post any. What did I do wrong???
126
People 150 / Slight hesitation
« on: September 15, 2012, 11:05:06 AM »
I have a People 150. The carb, jetting and airbox are all stock. The ignition is stock except for a iridium spark plug. I have installed a NHRC exhaust system, a 1500rpm contra spring, and replaced the stock 15gram rollers with 13gram rollers. The scooter takes off great, then has a slight hesitation, then picks up again right up throught the power band. Top speed is a GPS verified 60mph. Scooter runs and starts great other than that hesitation. I believe the hesitation was there when new, but seems more pronounced with the mods I've made. Any suggestions?
127
Technical | How To / Magnetic drain plug?
« on: September 06, 2012, 01:51:50 PM »
I have a people 150. Before changing the oil this time, I purchased a prima magnetic bolt oil drain kit (part # 1300-1007). In order to install the bottom bolt, I have to eliminate the spring and screen. The magnet won't let the spring seat properly. Is this the correct way???
128
Technical | How To / measuring variator rollers
« on: July 23, 2012, 11:47:05 AM »
I have a 2010 Kymco people 150. I want a little more performance out of it, so I'm goint to install lighter rollers and a 1000lb clutch spring. I want to take it apart today and see what my stock rollers are. I have a postal scale to weigh them, but I don't know what measurements I need. How do I measure to ensure I order the correct rollers?
129
People s150 / suggested jet size
« on: July 14, 2012, 02:35:27 PM »
I have a 2010 people 150. I pulled the stock plug at 600 km and it is burning lean. I am going to install a new NHRC alloy exhaust and will re-jet at that time. I need some size suggestions because I don't know what size jet is in it stock, and do not want to pull it apart until I have the replacement jets in hand . I'm just doing the exhaust for looks and sound. I am leaving the air filter and the rest of the scooter alone. It does a verified 60mph and I'm happy with that.
130
Technical | How To / Running lights
« on: July 01, 2012, 07:33:51 PM »
I recently purchased a new (2010) people 150. I love the scooter so far, but those front turn signal lenses that aren't utilized are a waste. I would like to install bulbs and sockets in them and wire them with the headlamp to be running lights. Are there any potential electrical problems with doing this? I also would like to change the tail/stop bulb and the working turn signal bulbs to LEDS. Where can I find replacement bulbs?
131
Technical | How To / NHRC exhaust system
« on: June 19, 2012, 12:05:35 PM »
I just saw pictures of a people 150 with the NHRC alloy exhaust system. I really like the looks of it and would like one. The question is whether it will effect the warranty on my brand new (2010) scooter.
132
Technical | How To / proper oils?
« on: June 17, 2012, 08:22:28 PM »
After looking around, I could not find a 15-40 full synthetic oil. I am going with Mobil 1 10-40 for the motor, and Mobil 1 75-90 for the transmission. Will there be any problems mechanically or with the warranty with these choices?
133
People 150 / Difference between years
« on: June 14, 2012, 09:56:21 AM »
I just bought my "new" people 150 with only 5 miles on it. The registration says it is a 2010 year model. I've seen 2011 & 2012 models advertised on line and they all look the same.. I'm wondering if the "newer" models have any improvements that I might incorporate on my 2010?
134
Technical | How To / Synthetic oil or not
« on: June 13, 2012, 08:18:48 PM »
I just bought a new people 150. I run full synthetic oil in everything else I own. The dealer I bought the scooter from does not recommend full synthetic for my scoot. What are your thoughts, and if I change over. How soon?
135
People 150 / Another new member
« on: June 13, 2012, 07:34:27 PM »
I'm a 68 year old male whose Harley got too big and heavy for him. I just bought a brand new (2010) people 150. Only rode it on a test run so far, but I think it will be a fun toy. Looking foreward to members expertise in this column.