KymcoForum.com
General => Technical | How To => Topic started by: 2016UXV500i on June 07, 2022, 04:01:19 PM
-
Looking for some help with what a fault code P1110 is on a 2016 UXV 500i. Will start the shutoff and that is the code that is displayed. Happens randomly then goes away.
-
I don't see a P1110 code listed. You sure it's not P0110?
This list was lifted from the Kymco Service manual
Blinks Failure Codes Fault description Priority Fault management
1 P0217 Engine temperature overheat 1 1.Stop immediately and check CELP code.
2. Check if the engine temperature sensor or electric circuit is faulty.
3. Check engine lubrication and cooling systems.
4. Check engine ignition and fuel systems.
2 P0335 Crankshaft position sensor or circuit malfunction 2 1. Check if the crankshaft position sensor, its connector, or wiring is faulty.
2. Make sure the generator rotor is aligned with the crankshaft position sensor.
3 P1120 Throttle position sensor setting value problem 2 1.Check if the TPS connector or wiring is faulty.
2.Check if the TPS is adjusted.
4 P1121 Throttle position sensor output range problem 2 1. Make sure the TPS connector is connected correctly.
2. Inspect the TPS
Blinks Failure Codes Fault description Priority Fault management
5 P1122 Throttle position sensor movement speed problem 2 1. Make sure the TPS connector is connected correctly.
2. Inspect the TPS
6 P0560 Battery voltage malfunction 1 1. Check the battery voltage.
2. Inspect the charging system.
7 P0110 Intake air temperature circuit malfunction 2 Inspect the T-MAP sensor
8 P0410 Idle air valve circuit malfunction 2 1. Check if the ISC connector or wiring is faulty.
2. Check the resistance of the idle air valve.
9 P0505 Idle speed volume control range problem 3 1.Check the ISC steps range with the diagnostic tool.
2. Check throttle body for carbon deposits.
3. Check intake for air leaks
10 P0251 Injector or electric circuit problem 2 1. Make sure the fuel injector connector is connected correctly.
2. Check if the ECU sends a signal to the injector.
3. Check the power source and resistance of the injector.
4. Make sure the battery is fully charged and connected correctly.
Blinks Failure Codes Fault description Priority Fault management
11 P0350 Ignition coil or electric circuit malfunction 2 1. Make sure the ignition coil connector is connected correctly.
2. Check if the ECU sends a signal to the ignition coil.
3. Check the ignition coil power source and resistance.
4. Make sure the battery is fully charged and connected correctly.
12 P0230 Fuel pump relay or electric circuit malfunction 2 1. Make sure the relay and pump connectors are connected correctly.
2. Check if the ECU sends a signal to relay.
3. Check the fuel pump relay resistance
13 P0219 Engine speed has exceeded top speed 2 Check if the CVT belt is broken.
14 P1560 Sensor doesn’t receive power source from ECU 2 1. ECU output to each sensor should be 5 DCV.
2. Check if the power source for all sensors is 5 DCV.
3. Check for a problem in the wiring harness.
4. If the CELP still blinks replace the ECU with a new item even if the output power source of ECU is normal.
15 P0700 Engine starting speed exceed CVT speed limited 2 Not used.
16 P0115 Engine temperature sensor or electric circuit malfunction 2 1. Make sure the WTS connector is connected correctly.
2. Check if the ECU pin is broken.
3. Check if the resistance of the sensor is out of specification.
17 P1561 Temperature gauge electric circuit malfunction 2 Not used.
Blinks Failure Codes Fault description Priority Fault management
18 P0650 CELP electric circuit malfunction 3 1. Check if the CELP bulb is faulty.
2. Check the CELP wires for damage.
21 P0105 Atmospheric Pressure Sensor/Circuit Malfunction 2 1. Make sure the MAP sensor connector is connected correctly.
2. Check if the ECU pin is broken.
3. Check the sensor voltage.
4. Use Diagnostic Tool to check the pressure.
22 P0110 Roll sensor or electric circuit malfunction 2 1. Make sure the sensor is installed in the correct position.
2. Check the sensor voltage.
3. Check if the ECU pin is broken.
-
Almost positive it was a P1110. I noticed in the list you sent me P0110 is listed twice. I think it may be a misprint and the 22 blink may be a P1110. Not sure why they would use the same code twice.
-
Almost positive it was a P1110. I noticed in the list you sent me P0110 is listed twice. I think it may be a misprint and the 22 blink may be a P1110. Not sure why they would use the same code twice.
Items 7 and 22 list P0110 first in#7 intake pressure then #22 for roll sensor. Like souzamoto said there is no P1110.
When the CELP (check engine light) blinks, it will blink seven short flashes for, let's say P0110. It will not blink any code flashes for the actual fault code. If #22 there would be two long flashes and the two short flashes.
How did you first determine code P1110 in the first place? With no service manual?
-
I'm a little late on this topic but the P1110 code just came up on my atv. I was tracing out a wiring problem and had not reconnected the rollover sensor. Plugged it back in and code went away.
-
I should have mentioned I have a service manual however the actual 'P1110' was on the bottom right of the display so no need to count CELP flashes.