KymcoForum.com
General => Technical | How To => Topic started by: TD46 on June 10, 2019, 02:22:47 AM
-
Hey all newb here and first kymco. Heck first scooter in a long long time lol. Just bought this today with title. Scoot has 47 miles on it. Its in mint condition. 1 owner. A guy bought it for his nephew who rode it 1 day then his nephew passed away. I know,i know horrible circumstances. Well they put it in storage for last few yrs now there moving and decided to sell it. Here are my issues. Charged the battery horn brake lights and turn signals work and high beam works. Starter button doesnt turn it over i do hear a slight clicking sound i assume is coming from starter relay. Kick starter cranks fine but not trying to start. Fresh gas and oil. Soooo what advice would you guys have as far as wear i should start? Sorry for long post just trying to let you all know the whole situation.
-
Clean the carburetor thoroughly. Clean all connections from the battery to the starter thoroughly.
-
Clean the carburetor thoroughly. Clean all connections from the battery to the starter thoroughly.
Ok i sure will. I did take a look quickly that is and the battery terminals look great brand new no corosion at all. Thanks for quick reply. I will be getting into it tom am and will post update. Thanks again
-
p.s. I'd also check voltage at the starter relay.
-
A few years is how many? I suspect your battery is sulfated and will never hold a proper charge. Load test will verify this. Replace if it fails the load test.
-
p.s. I'd also check voltage at the starter relay.
Ok i sure will. Gonna be diving into it here in a couple hrs. Thanks again.
-
Roughly 3 yrs. he did say he just replaced the battery though. Does look new although it was dead once i got it home and tried starting it. Also appears to be a cheap one from carquest. I was gonna pull the 1 from my zuma that i know is a new/better one and see.
-
Yuasa or Chrome for batteries....
-
UPDATE - Ok i got it everything off. All connections are tight and very very clean like new zero corrosion. Still cant get it to turn over with starter button. Relay has a slight click. I can kick start it which is very strong as i suspected since it only has 50 miles on it. Took the starter out looks brand new spins freely by hand. Id hate to have to just start buying parts - relay - starter - ignition coil etc. Any ideas? Thanks!
-
How much voltage are you getting at the starter relay?
-
Didnt get a chance today to check. I will check that in the am. Thanks!
-
How much voltage are you getting at the starter relay?
Ok mind you im far from a electrician but solid red wire for relay 12.5 red wire with white stripe ( assume for starter) 0. Battery 12.7 bout to pull my hair out. Wish i knew more about electrical
-
is this the part that clicks when you hit the starter button?
-
is this the part that clicks when you hit the starter button?
Yes the starter relay. I also assume the red wire with white stripe wont have power till the relay closes (clicks) to relay power to the starter so it will be dead until relay closes if im understanding it all correctly. Soooo took the starter out as ive mentioned previously hooked a wire up to my positive terminal on my battery then to the positive terminal on starter then hooked a ground up,to the flange on the starter then clipped the other end of ground to clean spot on frame and nothing starter still wouldnt work.now again battery showing 12.7 volts so looks like new starter it is. Thoughts? Hopefully this will get it to at least crank over
-
Having trouble finding starter for it. Anyone know of a place i can get 1. Thanks!
-
Yes the starter relay. I also assume the red wire with white stripe wont have power till the relay closes (clicks) to relay power to the starter so it will be dead until relay closes if im understanding it all correctly. Soooo took the starter out as ive mentioned previously hooked a wire up to my positive terminal on my battery then to the positive terminal on starter then hooked a ground up,to the flange on the starter then clipped the other end of ground to clean spot on frame and nothing starter still wouldnt work.now again battery showing 12.7 volts so looks like new starter it is. Thoughts? Hopefully this will get it to at least crank over
If you properly bench-tested the starter and it doesn't work, then, yes, the starter is your problem.
-
But it's unusal for a scooter with only 50 miles on it to need a new starter, no matter how old it is.
-
Yes the starter relay. I also assume the red wire with white stripe wont have power till the relay closes (clicks) to relay power to the starter so it will be dead until relay closes if im understanding it all correctly. Soooo took the starter out as ive mentioned previously hooked a wire up to my positive terminal on my battery then to the positive terminal on starter then hooked a ground up,to the flange on the starter then clipped the other end of ground to clean spot on frame and nothing starter still wouldnt work.now again battery showing 12.7 volts so looks like new starter it is. Thoughts? Hopefully this will get it to at least crank over
Rather clip the other end of the earth from the starter flange directly to the earth terminal on the battery, instead of clipping the earth to the frame. That should eliminate the possiblility of a bad earth conection.
-
Rather clip the other end of the earth from the starter flange directly to the earth terminal on the battery, instead of clipping the earth to the frame. That should eliminate the possiblility of a bad earth conection.
Yea i did that and it was toast. Wouldnt turn and started smoking. Did a compression test and 52 psi so time for a rebuild. Should i remove the engine and tear it all the way down? Or leave it in and just do the top end? Never did a rebuild before so i wanna do it the right way. With so many kits out there what and where should i purchase one? Thanks for your help much appreciated.
-
Yea i did that and it was toast. Wouldnt turn and started smoking. Did a compression test and 52 psi so time for a rebuild. Should i remove the engine and tear it all the way down? Or leave it in and just do the top end? Never did a rebuild before so i wanna do it the right way. With so many kits out there what and where should i purchase one? Thanks for your help much appreciated.
I don’t understand - How did you manage to do a compression test if the starter motor did not swing the engine ?
Anyway, to determine what needs to be rebuilt I think it will make sense to get a new starter motor first - and then to do a “dry†and “wet†compression test on the engine.
To do a “wet†compression test you just need to squirt a lil’ bit of oil into the engine via the spark plug hole.
If you get a higher compression reading during the “wet†test, it means the cylinder sleave or piston rings are worn, or the ring gap is too big.
If the compression reading remains the same during a “wet†compression test, it means the cylinder head needs a rebuilt.
P.S. IMPORTANT. If you got that 52 Psi reading while the starter motor was cooking (turning the engine slowly) you should not rely on that initial compression reading. To do a proper compression test the starter motor needs to work properly, and needs to swing the engine properly.
-
I don’t understand - How did you manage to do a compression test if the starter motor did not swing the engine ?
Anyway, to determine what needs to be rebuilt I think it will make sense to get a new starter motor first - and then to do a “dry†and “wet†compression test on the engine.
To do a “wet†compression test you just need to squirt a lil’ bit of oil into the engine via the spark plug hole.
If you get a higher compression reading during the “wet†test, it means the cylinder sleave or piston rings are worn, or the ring gap is too big.
If the compression reading remains the same during a “wet†compression test, it means the cylinder head needs a rebuilt.
P.S. IMPORTANT. If you got that 52 Psi reading while the starter motor was cooking (turning the engine slowly) you should not rely on that initial compression reading. To do a proper compression test the starter motor needs to work properly, and needs to swing the engine properly.
Sorry i should of explained it a bit more. My neighbor has a couple scooters just laying around so i went and took a look and found the same starter on 1 of them so i bench tested it and it ran fine so then i installed that 1 to do the compression test. I did not do a wet test so i will do that first thing in the morning. Also once i installed the good starter and was trying to get it to start there were multiple times when i would try the kick start just to give the electric starter a break and kick start was locked up. Not the actual kick start but the engine few times i couldnt budge the kick starter. Electric starter also a few times would lock up i would then try kick start and same locked up so i would take spark plug out hit tue electric start couple times sometimes that would free it up other times id bump the electric start then really jump on the kick start to free it up.
-
Don't get carried away, changing the starter, relay, wiring, valve-job, etc. The battery is DEAD! They totally die when sitting in storage. It's simple as ABC: replace the battery, clean the carburetor, and put in fresh gas. It'll start first time.