Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - shalbern

Pages: 1 2 [3] 4
31
People 250 / Re: Oil Screen Size
« on: May 21, 2011, 11:59:10 PM »
OK, so who dares to measure?

Are there no Caliper Christophers out there in internet land?

Are there no Measuring Marvins?

Are there no Dial Indicator Davids?

Are there no Ruler Roberts?

 

32
People 250 / Re: People 250 Fork Oil replacement
« on: May 18, 2011, 01:59:45 AM »
Hi.

How do you fill the fork with the new oil?

Thanks

33
People 250 / Oil Screen Size
« on: May 17, 2011, 06:10:41 AM »
 ??? Hi,

Does anyone know the outside diameter in mm of the rubber portion of the oil screen for a 2007 p250?
They sell one that's 26 mm and one that's 27 mm. Which one should I buy?

Thanks in advance

34
People 250 / Re: Aftermarket Muffler
« on: January 18, 2011, 05:54:52 PM »
Hi,

Here's the link to the exhaust system I was referring to:

http://cgi.ebay.com/ebaymotors/Performance-Exhaust-Kymco-People-250cc-scooters-_W0QQcmdZViewItemQQhashZitem335b3e00b4QQitemZ220574122164QQptZMotorcyclesQ5fPartsQ5fAccessories


It is any good at $145 + $100 shipping?

35
People 250 / Aftermarket Muffler
« on: January 16, 2011, 03:11:45 AM »
Hi,

Has anyone purchased one of those $300 aftermarket stainless steel mufflers advertised in ebay?
Is it any good, or is just replacing the stock muffler a better way to go?

Thanks in advance.

36
People 250 / Re: Turn Signal Lights
« on: October 07, 2010, 01:22:09 AM »
Hi Tech Guy,

What was the part number for your "no load" flasher relay, and where did you get it?

Where is the relay located on my p250?

I want to try that mod.

Thanks


37
People 250 / Re: License Plate Light
« on: October 02, 2010, 09:17:23 PM »
Thanks,

I found the two small screws, but in order to get to them it seems that the entire license light assembly must be removed, Is that true? If so, what are the specific removal instructions?

Thanks in advance

38
People 250 / License Plate Light
« on: September 29, 2010, 05:49:29 AM »
Hi Again,

Well it's a good thing there are experts who have done this kind of stuff out there!

What is the best way to replace a burned out license plate light on my 2007 p250?

I looked at the manual and it really does not mention how.

Thanks in advance

39
People 250 / Turn Signal Lights
« on: September 27, 2010, 02:06:44 AM »
Hi,

2 Quick Questions about my 2007 p250.

1. What is the common or "GE" number for the front and rear turn signal light bulbs?

2. Can a LED replace these bulbs directly without the system going wakco?

Thanks in advance

40
People 250 / Re: Stall when stopping -updated and solved-
« on: September 15, 2010, 02:43:37 AM »
Hi,

I'm no expert but if it stalls, especially when you first fill it with gas, then it has a vapor lock issue.

That's what happened to me and my 2007 p250. I finally wound up drilling a 1/64 inch hole in the top of the rubber portion of the gas cap to keep it vented at all time.

Stalling problems were gone for good. (At least for the last 2 months)

Have a good ride !

 

41
People 250 / Dipstick
« on: September 10, 2010, 11:35:37 PM »
Hi,

Someone swiped the oil dipstick off my 2007 p250 while it was parked. !@#$%^&

Where can I find a replacement?

I looked at Stadium Yamaha, I did not not see one on their parts pages, maybe I was looking in the wrong place.

Thanks in advance.

42
People 250 / Re: CONFIRM/DENY: Front brake pads same as Kawa Ninja 250?
« on: September 05, 2010, 04:15:29 AM »
So what is the final result?

I need to buy a set for the front and rear of my 2007 p250.

Do I buy 2 sets of of EBC FA197s or 1 set of the FA197 and another set of ????

My rear pad does not have the ears, will ears still work in the rear?

I'm confused !!

Thanks in advance

43
People 250 / Re: Strange Happenings
« on: August 16, 2010, 10:04:25 PM »
FYI

Vent cleaned, problem solved !!!

Thanks

44
People 250 / Re: Strange Happenings
« on: August 16, 2010, 04:39:35 AM »
Hi,

If you take the four springs out of the gas cap, will that prevent the cap from sealing and allow gas vapors to leak out. If these spring were replaced with ones with less tension, would that work better?


Thanks

45
People 250 / Strange Happenings
« on: August 14, 2010, 05:19:07 AM »
Hi,

My 2007 p250 has been acting strange lately. It usually runs just great expect just after I fill it up with gas. Then it won't idle for a short while, especially when it's hot. After it cools down it runs just fine until it needs to be filled with gas again. Any ideas on what's happening?

Thanks in advance

Pages: 1 2 [3] 4