Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - MrXT

Pages: [1]
1
Agility 125 / Brake pads for agility city 125
« on: December 28, 2019, 07:07:06 PM »
Anyone know if the brake pads for the agility city 125 are the same back and front or if the front and back pads are different?

2
Agility 125 / Center stand rubber stopper
« on: December 11, 2017, 08:07:33 PM »
My rubber stopper has eroded and now the bike squeeks like hell anytime i sit on it or go on a slight bump so need to replace it but cant find a proper replacement part. Does the rubber stopper for the normal agilty work on the agility city?
I tried ordering from https://www.bike-parts-kymco.uk/ but they have been a nightmare, they refuse to speak english and sent me the wrong part they sent the side stand rubber stopper instead and wont reply to emails now. (AVOID THEM!!!) Is there anywhere else i can source this part?

3
Agility 125 / Wont stop cranking
« on: April 01, 2016, 08:51:18 PM »
Once again I got back from shopping and i turned my engine off but the bike kept cranking. I felt something was off with the bike the whole trip back it was making an odd clicking sound all the way home and when I shut off the bike it kept trying to start until the battery drained before I could disconnect it.

I paid a garage to fix this issue so they obviously didn't replace anything. I'm assuming this is the starter solenoid? So I should replace this right?

4
Agility 125 / Agility city break pads?
« on: April 01, 2016, 03:21:47 PM »
Does the agility city use the same break pads for the front and rear or are they slightly different? I can see lots of listings for front pads but not rear.

5
Technical | How To / Plastic windshield bolts
« on: February 08, 2016, 05:46:23 PM »
Does kymco sell these for when we lose them? My bike got blown over in the wind and now iv lost all 4 plastic bolts that clip the stock windshield on my kymco agility city. Any one know where I can get replacements?

6
Agility 125 / Strange noise and feel when bike hits 40mph
« on: February 03, 2016, 11:05:33 PM »
As soon as my agility city goes over 40mph I get this strange vibration or grinding feeling coming from the bike, its hard to describe tho. The bike also doesn't go much faster than about 55mph. Any idea what the problem night be?

7
Agility 125 / Bike sounds like its really straining
« on: October 15, 2015, 12:50:35 AM »
My kymco agility city runs fine up to about 40mph and then it feels like its running at 100% with a weird chug feeling under my ass. Weird description but its the best wording I can think to use. Any idea what's causing it?

8
Technical | How To / How to video please!!!
« on: September 03, 2015, 12:39:07 AM »
Can someone record the removal of the front plastic cover where the brake fluid reservoir is on any of the following models -super 8,agility, agility r16, agility city or any similar model. I have the agility city and there are no instructions for how to remove this cover so I can access the brake fluid reservoir please help!!!

9
Agility 125 / Air filter compatibility
« on: August 26, 2015, 10:50:48 AM »
Will the kymco agility r16 city 125 air filter fit the kymco agility city 125? It looks pretty much the same but is cheaper.


10
Agility 125 / Carb running very lean
« on: May 28, 2015, 01:13:19 AM »
Changed my spark plug and it looks like my engine is running very lean.

Does anyone know the correct air/fuel screw setting?  Although I have the agility city I'm sure the carb and engine is completely the same.

11
Agility 125 / Brake fluid
« on: April 19, 2015, 07:46:10 PM »
Manual recomends dot4 but it doesn't say synthetic or non synthetic so what's in it from stock??? Am I forced to bleed the brakes before topping it up the first time??

12
Agility 125 / Missing two screws help!!
« on: March 11, 2015, 06:00:58 AM »
Im missing 2 screws in the right switch gear thing

http://www.exportstrength.com/images/kymco_agility_50_right_hand_switch_as.jpg

This thing the two screws that hold the 2 halves together have fallen out. I actually have the agility city 125 but im sure it would be the same, so does anyone know exactly what screws i need to replace them with? type of screw including thread size?

Help removing the plastic to get the screws in easier would also help but just identifying exactly what screws i need is priority.

At the moment i just have it ducktaped but that falls off after a short time.

Pages: [1]