Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - TLRam1

Pages: [1] 2 3 ... 26
1
People 250 / Re: People S 250 reboot
« on: May 13, 2018, 11:52:17 PM »
RatBob,

How do you get the front cover off. I have had it loosened to replace the horn but it was still connected to the lower body cover and I could not remove it, I did undo the 2 screws behind the tire.

How do you get the front cover off, do you have pics you can post?

2
General Discussion / Re: Valve Stem Hole Size
« on: May 05, 2018, 07:38:57 PM »
I ordered these angled Red ones, we will see how they fit. If you have never had solid mount angled stems (not the ones that are snapped in and held by the rubber bottom part of the stem), you would be in for a pleasant experience, much easier to check tire pressures and add air.

3
General Discussion / Re: Valve Stem Hole Size
« on: May 03, 2018, 02:36:35 AM »
Yes I would think they are the same on most all the Kymco line, thanks for the input.

4
General Discussion / Valve Stem Hole Size
« on: May 02, 2018, 06:34:01 PM »
Replacing my rubber stems with aluminum, do you know what size hole is in the rim?

The stems I want are 11.3 MM, do you know if these will fit? If it matters I run a 250 S People.  One catalog list these as Japs are 11.3 and Euro & aftermarket are 8.3 MM.

5
Kymco News / Re: New Kymco website
« on: December 07, 2017, 06:23:41 PM »
Quote from: big blue on December 07, 2017, 05:25:53 PM
Here's the KYMCO USA link...http://kymcousa.com/

TY

6
Kymco News / Re: New Kymco website
« on: December 07, 2017, 09:06:14 AM »
Link?

7
People GT 300i / Re: Top box trunk rattle. How to fix?
« on: November 12, 2017, 06:50:05 AM »
I used foam weather stripping in the channels of my Shad case, it worked.

8
People 250 / Re: P250 windshield
« on: September 30, 2017, 12:40:39 AM »
Stu,

I don't have one I want to sell, as you are aware, these are hard to come by. I had to put one in the oven to make it fit, the Givi I have, the mount hardware I searched the world over and had to get a forum member (from another forum) in France to assist in getting the kit to the states for me.

The guy did not ask for any money until I received the kit from him, great guy. As you say I don't know that the two shields are interchangeable.

9
People 250 / Re: P250 windshield
« on: September 29, 2017, 06:27:23 AM »
Columbia scooters used to have one that fit the PS250, I think PUIG had one also.

10
People 250 / Re: P250 windshield
« on: September 29, 2017, 06:05:50 AM »
Do you want OEM size? I have the PS250 but I think the PS might be different, can't remember.

11
Downtown 300 / Re: TRIMMING DOWN MY WINDSHIELD TO MEET WITH MY NOSE :)
« on: September 20, 2017, 06:57:17 AM »
Looks like you have this handled, not difficult, use a jigsaw fine blade. little edge conditioning needed after this.   

12
Technical | How To / Re: Charging system output
« on: August 31, 2017, 05:41:15 AM »
I would like to know on the People S250.

13
People 250 / Re: Carburetor kymco 250 people s and high speed problem, black spark
« on: May 22, 2017, 05:32:19 AM »
What country are these in?

14
People 250 / Re: Carburetor kymco 250 people s and high speed problem, black spark
« on: May 21, 2017, 02:36:50 AM »
Beautiful!

15
Eye Candy | Videos and Pics / Re: Scooter Girl rides again!
« on: May 17, 2017, 05:45:16 AM »
Where in Texas?

Pages: [1] 2 3 ... 26