I don't see a P1110 code listed. You sure it's not P0110?
This list was lifted from the Kymco Service manual
Blinks Failure Codes Fault description Priority Fault management
1 P0217 Engine temperature overheat 1 1.Stop immediately and check CELP code.
2. Check if the engine temperature sensor or electric circuit is faulty.
3. Check engine lubrication and cooling systems.
4. Check engine ignition and fuel systems.
2 P0335 Crankshaft position sensor or circuit malfunction 2 1. Check if the crankshaft position sensor, its connector, or wiring is faulty.
2. Make sure the generator rotor is aligned with the crankshaft position sensor.
3 P1120 Throttle position sensor setting value problem 2 1.Check if the TPS connector or wiring is faulty.
2.Check if the TPS is adjusted.
4 P1121 Throttle position sensor output range problem 2 1. Make sure the TPS connector is connected correctly.
2. Inspect the TPS
Blinks Failure Codes Fault description Priority Fault management
5 P1122 Throttle position sensor movement speed problem 2 1. Make sure the TPS connector is connected correctly.
2. Inspect the TPS
6 P0560 Battery voltage malfunction 1 1. Check the battery voltage.
2. Inspect the charging system.
7 P0110 Intake air temperature circuit malfunction 2 Inspect the T-MAP sensor
8 P0410 Idle air valve circuit malfunction 2 1. Check if the ISC connector or wiring is faulty.
2. Check the resistance of the idle air valve.
9 P0505 Idle speed volume control range problem 3 1.Check the ISC steps range with the diagnostic tool.
2. Check throttle body for carbon deposits.
3. Check intake for air leaks
10 P0251 Injector or electric circuit problem 2 1. Make sure the fuel injector connector is connected correctly.
2. Check if the ECU sends a signal to the injector.
3. Check the power source and resistance of the injector.
4. Make sure the battery is fully charged and connected correctly.
Blinks Failure Codes Fault description Priority Fault management
11 P0350 Ignition coil or electric circuit malfunction 2 1. Make sure the ignition coil connector is connected correctly.
2. Check if the ECU sends a signal to the ignition coil.
3. Check the ignition coil power source and resistance.
4. Make sure the battery is fully charged and connected correctly.
12 P0230 Fuel pump relay or electric circuit malfunction 2 1. Make sure the relay and pump connectors are connected correctly.
2. Check if the ECU sends a signal to relay.
3. Check the fuel pump relay resistance
13 P0219 Engine speed has exceeded top speed 2 Check if the CVT belt is broken.
14 P1560 Sensor doesn’t receive power source from ECU 2 1. ECU output to each sensor should be 5 DCV.
2. Check if the power source for all sensors is 5 DCV.
3. Check for a problem in the wiring harness.
4. If the CELP still blinks replace the ECU with a new item even if the output power source of ECU is normal.
15 P0700 Engine starting speed exceed CVT speed limited 2 Not used.
16 P0115 Engine temperature sensor or electric circuit malfunction 2 1. Make sure the WTS connector is connected correctly.
2. Check if the ECU pin is broken.
3. Check if the resistance of the sensor is out of specification.
17 P1561 Temperature gauge electric circuit malfunction 2 Not used.
Blinks Failure Codes Fault description Priority Fault management
18 P0650 CELP electric circuit malfunction 3 1. Check if the CELP bulb is faulty.
2. Check the CELP wires for damage.
21 P0105 Atmospheric Pressure Sensor/Circuit Malfunction 2 1. Make sure the MAP sensor connector is connected correctly.
2. Check if the ECU pin is broken.
3. Check the sensor voltage.
4. Use Diagnostic Tool to check the pressure.
22 P0110 Roll sensor or electric circuit malfunction 2 1. Make sure the sensor is installed in the correct position.
2. Check the sensor voltage.
3. Check if the ECU pin is broken.
