Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - de dee

Pages: 1 2 [3]
31
Downtown 300 / brake pads what kind to buy
« on: July 29, 2013, 01:07:33 AM »
checking the tires and brakes, looks like new ones again,.  Im going for power pure by michelin,  but the brakes I dont know what to buy,. or just order from kymco supplier,.  any one know what is a good brake pad for 300i downtown  22.000 miles and loven it!!!   Don,

32
Downtown 300 / DNA filters for GT i300 & 300i downtown
« on: June 04, 2013, 02:41:07 PM »
  if anyone is interested,  I will order  DNA filters for gt i300  &  300i downtown, any takers,. 

33
Downtown 300 / raising the gear ratio
« on: April 25, 2013, 07:06:30 PM »
   I tryed using 23/12  16 gram rollers ,,. made it by putting heat shrink around it,.  dont work!  next I am trying 1 mm spacer behind variator,,. going for a run now  !!! hope it works to get the RPM down ,.

34
People GT 300i / importing a GT.300i with abs brakes,.
« on: April 08, 2013, 04:28:44 AM »
 I made a inquirery to a dealer in Italy, for a gt. 300i ,.we do not get them in canada,at all, so I would like to know what it costs to get one here, and I would order it with abs brakes,. should get a answer next week,.

35
Downtown 300 / seat foam I spoke to my upholster
« on: March 25, 2013, 12:31:15 AM »
   the upholsterer said go to a upholster shop and pick out the foam you want ,. I picked the firm one for my scoot, now I am ready to begin changing my seat again, I will have the same firmness from front to back of seat,    I picked up a 1 inch wide belt sander to shape the foam,. I was told to wear googles and face filter as the foam is very fine ,. not good to breath or get into eyes,.

36
Downtown 300 / WOLO horn install on downtown
« on: March 20, 2013, 03:45:23 AM »
   I pick up a wolo horn at harbor freight,it warmed up enough to install the horn the other day  before this snow storm that is ongoing, I removed the front clip to see what I could do,. ended up it bolted in no trouble ,.  on the same bar as original,. just below it is a good spot to bolt it on, removed the hang down bar from original spot and used the bar to off set horn and it fits perfectly,.   it seems to be twice as loud,. I used the same wiring off the old horn just plug it on,. I have a over sized battery, so other scoots may have to run a wire from the battery,. to get enough power to the horn,.

37
Downtown 300 / were do I find a 3mm. spanner
« on: March 20, 2013, 03:28:22 AM »
   I have been to prices auto , canadian tire, and some auto supply places, no luck so far, has any one done a valve adjustment on there downtown, what did you use to hold valve adjust screw and tighten lock nut,.

38
Technical | How To / dr. pulley sliders or rollers
« on: January 31, 2013, 06:37:51 PM »
   what side should the rollers face left or right ,. and when you install them , face them right , and install them at 12 oclock  or 6 oclock,. I cant tell from watching the vidios,. seems different people do it one or the other,.   thank for any info,.

39
Technical | How To / iridium spark plugs good for how many miles,
« on: January 23, 2013, 08:45:39 PM »
  I HAVE 22,000 KM. ON SPARK PLUG, ON A 300I DT.  ON MY TOYOTA SIENNA i HAVE 200,000 KM. WHAT IS THE LIFE OF THESE PLUGS ON DIFFERENT ENGINES,.

Pages: 1 2 [3]