« previous next »
Pages: [1] 2 3 ... 7

Author Topic: STARTING PROBLEMS  (Read 10317 times)

5029lee

  • Newbie
  • *
  • Posts: 6
    • View Profile
STARTING PROBLEMS
« on: June 17, 2010, 08:55:46 AM »
hi, i have had a new battery and if i have it on a battery charger my kymco kicks up fine, leave it over night and i cant get it to kick up, charge battery again it kicks up,(only needs a little charging about 10 mins) cant get it to kick up of kick start,and scooter will run if i disconnect battery so i think alternator's must be fine any clues, cheers lee
Logged

sticlistul

  • Full Member
  • ***
  • Posts: 150
  • Sex, Scoot and Rock 'n' Roll
    • View Profile
Re: STARTING PROBLEMS
« Reply #1 on: June 17, 2010, 11:53:24 AM »
did you try an other battery ?? maybe your battery is loosing power , but it's not always from the battery ,at me after this winter didn't want t start at all at button ,I even put the car battery and nothing... just from kickstarter ,but after a kickstart and warmup the engine the button starts at a simple push ...
Logged

zombie

  • You never know do ya!
  • Hero Member
  • *****
  • Posts: 13870
  • Close enough to get the idea!
    • View Profile
Re: STARTING PROBLEMS
« Reply #2 on: June 18, 2010, 12:00:59 AM »
Put an amp meter between the battery terminal and the cable to see if there is something drawing power when the switch is off.
Logged
"They have nothing in their whole imperial arsenal that can break the spirit of one Irishman who doesn't want to be broken."   Bobby Sands...

wordslinger

  • Hero Member
  • *****
  • Posts: 10766
  • undead primate
    • View Profile
Re: STARTING PROBLEMS
« Reply #3 on: June 19, 2010, 02:04:32 AM »
...it's probably the starter motor...mine did the same thing, and i found that the starter's magnets had broken free of the casing...
Logged
..every mod (action) necessitates a (reaction) mod..

joeboy

  • Full Member
  • ***
  • Posts: 107
    • View Profile
Re: STARTING PROBLEMS
« Reply #4 on: June 20, 2010, 03:57:21 AM »
Sounds like the battery has a bad cell, ive had this before with a new battery.
Logged

joeboy

  • Full Member
  • ***
  • Posts: 107
    • View Profile
Re: STARTING PROBLEMS
« Reply #5 on: June 20, 2010, 04:43:31 AM »
I forgot to mention you also need to check that the machine is charging when it is running.
Logged

oswaldters

  • Hero Member
  • *****
  • Posts: 1158
    • View Profile
Re: STARTING PROBLEMS
« Reply #6 on: July 08, 2010, 09:59:51 PM »
Speaking of starting problems, I am also having problems getting the electric starter to work.

I have tested the battery - it is fine, fully charged, and putting out the correct amps.

I have tested the alternator - it is fine and keeping the battery charged

I removed the starter and it spins freely when I turn it with my hand.

Strange thing is sometimes the starter kicks in fine, sometimes it simply makes a clicking noise, sometimes it does nothing.  I can never predict what will happen when I try the electric starter.  I borrowed a battery jump starter and whenever I put that thing on, the starter works great.

Any ideas?
Logged

wordslinger

  • Hero Member
  • *****
  • Posts: 10766
  • undead primate
    • View Profile
Re: STARTING PROBLEMS
« Reply #7 on: July 08, 2010, 10:12:08 PM »
..yeah, i would suspect the starter motor, again...

..since i got my people, and am using the starter from my A50 on it..

..it's clear that the 4t engine requires a lot more work out of the starter motor than a 2t...

..especially if the 4t's idle mix isn't "spot-on"...

..the magnets came loose from the casing with my a50 starter...

...i rebuilt it with parts from a junker chinese scoot i have...
« Last Edit: July 08, 2010, 10:20:43 PM by wordslinger »
Logged
..every mod (action) necessitates a (reaction) mod..

oswaldters

  • Hero Member
  • *****
  • Posts: 1158
    • View Profile
Re: STARTING PROBLEMS
« Reply #8 on: July 10, 2010, 06:41:34 PM »
Yep, that sounds about right.  I discovered that hitting the starter with a hammer makes it work for a while.

Looks like it's time for a new starter.

Thanks for the help.
Logged

wordslinger

  • Hero Member
  • *****
  • Posts: 10766
  • undead primate
    • View Profile
Re: STARTING PROBLEMS
« Reply #9 on: July 10, 2010, 08:00:26 PM »
Looks like it's time for a new starter.

..or a bigger hammer...

 ;D

..post back with the results!


peace
Logged
..every mod (action) necessitates a (reaction) mod..

jay20

  • Jr. Member
  • **
  • Posts: 66
    • View Profile
Re: STARTING PROBLEMS
« Reply #10 on: August 05, 2010, 08:29:07 PM »
when i press the electric start on my scoot the bendix spins untill it hits the big cog then stops is that lack of power in my battery? Help please
Logged

wordslinger

  • Hero Member
  • *****
  • Posts: 10766
  • undead primate
    • View Profile
Re: STARTING PROBLEMS
« Reply #11 on: August 05, 2010, 09:38:48 PM »
..in the other thread you said the bendix is spinning counter-clockwise, right??

..it should spin clockwise, i do believe...

 :-\
Logged
..every mod (action) necessitates a (reaction) mod..

jay20

  • Jr. Member
  • **
  • Posts: 66
    • View Profile
Re: STARTING PROBLEMS
« Reply #12 on: August 05, 2010, 10:29:24 PM »
it is spinning anti clockwise but if it spun the other way it would not come out to bigger cog have i bought a sh**ter lol
Logged

wordslinger

  • Hero Member
  • *****
  • Posts: 10766
  • undead primate
    • View Profile
Re: STARTING PROBLEMS
« Reply #13 on: August 05, 2010, 10:32:03 PM »
..i have no idea what you've bought...

 ;D

..give us some history on your scoot...
Logged
..every mod (action) necessitates a (reaction) mod..

oswaldters

  • Hero Member
  • *****
  • Posts: 1158
    • View Profile
Re: STARTING PROBLEMS
« Reply #14 on: August 05, 2010, 10:56:08 PM »
Finally solved my starting problem.  I did replace the starter - took almost 3 weeks to get it shipped from Stadium Yamaha.  Scoot starts great now.

I even took apart the old starter to see what was going on, but couldn't figure out what the problem with it was. 


Logged

An Error Has Occurred!

Call to undefined function split()
Back