Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Wicked Al

Pages: 1 [2] 3 4
16
Side By Side / Re: UXV 700 Race Build
« on: June 28, 2015, 04:08:51 PM »
Nothing to hate. The 900s is a different class of vehicle. If you test drive a Rzr 1000, you will see another big step up in performance...for a few more dollars of course. The vehicles the Kymco compares against are other utility focused vehicles such as the Polaris Ranger, Honda Pioneer, Yamaha Viking etc. You say "only" $3000 more than the Kymco. If we're talking 10k and 13k, that's a 33% increase in price, for many that's a big change. When my kit is done, it will give essentially the same suspension performance as the 900s, 12 up front, 13.75 in back, but I can't make up the displacement difference in power. Good luck with your purchase, give us a long term report after you've had it a bit.

17
Side By Side / Re: 450i review
« on: June 25, 2015, 06:04:32 AM »
What kind of accessories are you looking for?

I'm in the process of building items for the UXV 700/500. I have a 450i sitting in the back, but haven't had a chance yet to tear into it to see what can be done. Most of what I'm doing starts with the suspension then goes from there to cages, doors, bumpers then engine improvements. I did notice that the 450i has a bit of positive camber to the front tires, didn't know if this was normal  or not.

How does it drive for you? Track straight? Sensitive steering? Pushes in corners? Anything odd at all with handling?

Where is the wear on the tires?

Any input you or other 450i owners have on handling would be appreciated and then I can take a look at that and see about removing issues.

Thanks!

Alex

18
Side By Side / Re: UXV 700 Race Build
« on: June 21, 2015, 09:56:41 PM »
Here is the chart with the computer and fuel controller, but adding a custom intake. The rpm difference was due to the guys shutting it down early and not doing a full pull. I'll get more charts after we add the clutch mod.

19
Side By Side / Re: UXV 700 Race Build
« on: June 21, 2015, 09:53:47 PM »
Here is the Dyno chart of going from stock to the computer and Dobeck fuel controller.

20
Side By Side / Re: Tire size on the 700 uxv
« on: June 06, 2015, 04:05:29 AM »
I'm sure other manufactures have tables like this too, http://cocomponents.com/dealer/wheel-specs/ you can see which wheel has the right offset. I haven't measured the stock wheels so don't know what they are. Bolt pattern is 4 on 110.

21
Side By Side / Re: UXV 700 Race Build
« on: June 06, 2015, 03:11:57 AM »
Dyno pulls, power to the ground.
Everything stock, 27" tires = 34hp
Computer and Dobeck fuel controller = 36hp + more rpm
We are working on an intake, should add 3-4hp
Next is an exhaust and we'll see where that takes us.
The head, piston and jug is on it's way to see what can be done to flow better there.

I'll post graphs once I get my hands on them.

22
Side By Side / Re: UXV 700 Race Build
« on: June 04, 2015, 05:01:48 AM »
Paul, I think that's a very good number. I know the limiter on mine kept it to 43mph. Check it against your smart phone if you have one. You can download a speed app so you can see how fast you are going regardless of tire size changes etc.

23
Side By Side / Re: Tire size on the 700 uxv
« on: June 04, 2015, 04:58:22 AM »
Laidback, looked up the Boss Hoss, agreed, wouldn't have to modify that motor at all, might need a slightly larger fuel tank though.

Paul, The tires are on MSA M-21 Lok wheels. These are 14x7 with a zero offset.  http://cocomponents.com/dealer/m21-lok-utv-wheels-beadlock/

Because there is no offset, it will make the vehicle a few inches wider as the stock wheels have a positive offset. Because I also did the wider tires in the back, I stretched the bed another 6 inches wider to accommodate the tires so they would tuck into the fenders on full compression.

24
Side By Side / Re: UXV 700 Race Build
« on: June 01, 2015, 03:33:11 AM »
Oh, you'll be happy alright, until you get to 55, then you'll want to do 60, then 65....I know how this works. Good luck with the mods. Let us know how well it goes!

25
Side By Side / Re: 700i Exhaust 'Afterfire'
« on: May 31, 2015, 11:55:33 PM »
I don't know yet what "normal" is for these machines. I know I had a Yamaha YFZ that glowed cherry red all the time and my Polaris Outlaw loves to pop and crackle under deceleration, these are normal behaviors for these bikes. It certainly isn't out of the question to be normal for the KYMCO.

26
Side By Side / Re: UXV 700 Race Build
« on: May 31, 2015, 11:51:12 PM »
I got some top secret stuff from KYMCO. I don't know if this is something they will offer, kinda doubt it as they need to protect warranties and such, or if it is something they will let me fool around with so I can offer it as an aftermarket part once we get it dialed in. Once I know, I'll post it here. For fuel I'm using the Dobeck fuel controller. There are no two ways about it, it's certainly running faster then before without any limiter action.

I dropped it off at my engine guys place on Saturday. We're going to get a baseline dyno run with everything stock except the tires. Then we'll do dyno pulls after every mod so we can see what benefit the various changes make to its performance. Computer, intake and exhaust are the first three things on the list. Then we'll look at piston, valves and cam along with headwork to see what we can get it to give up for ponies.

I just got into the bottom end of the one motor and it looks like everything is plenty beefy for performance mods, this is good to know and not have to worry about it.

Alex

27
Side By Side / Re: UXV 700 Race Build
« on: May 28, 2015, 05:15:50 AM »
Hey Laidback, I mentioned I needed power steering and a steering quickener, I don't have power steering yet on this one. I have it on another unit that is in parts right now, I briefly drove it and it worked great. My 700 topped out at 43mph. What it is actually doing now, I don't know. I changed the computer, my revs go up to 7500. I have 27 inch tires and I made some clutch changes. When I changed the computer my dash didn't give a readout, unless you want to believe I was doing 199kph :) I will be doing some dyno tuning in the near future and will be able to get some good numbers from that.

Race pictures are now up on my facebook page. https://www.facebook.com/warpoffroad

28
Side By Side / Re: UXV 700 Race Build
« on: May 26, 2015, 11:34:38 PM »
You Tube Video




Anyone know how to make this an actual video preview instead of just a link?

Thanks!

Alex


29
Side By Side / Re: UXV 700 Race Build
« on: May 26, 2015, 11:09:52 PM »
Well, Cedar City race is in the books!

I have a full report and video on my FB page, Like it if you would like to stay updated. https://www.facebook.com/warpoffroad



I'll copy the content here too.


Race Report:

WORCS Rd 6, 700 Production SxS, Cedar City, Iron Mine Utah.

Great things are happening in our KYMCO UXV 700 race program!
First I want to start off by saying Southern Utah has some beautiful country. I imagine that’s why they have so many National Parks.

Forecasts were NOT encouraging. They changed from day to day, but always rain. Sure enough, on Friday for the full course unclassified race, it was drizzling. Not bad as it was pouring earlier, but the track was sloppy. A guy on a quad had just come off the course…covered in mud, and suggested I would be better off not going out. Well, I had just mounted fresh Stage 5 shocks from Elka on the 700 and was anxious to see what they were like… so out I went.
It was sloppy in many areas, but not too bad in others. I tried to avoid the deeper ponds. I went through all of my tear offs, but all in all, it was good to be out there pre riding the course. Not only did I get a feel for the new shocks, which performed great, but I could also get used to the KYMCO as well. Given that I am new to SxS racing I had some technique to learn and limits to find out, practice is good for that.

My plan was to come out with new a-arms with the new shocks which would give me 12” of travel up front and 13.5” of travel in the back…didn’t happen. Arms are still a work in progress, I ended up with 10” up front and 11-12” in the back. Still way better than stock and with shocks that were sprung correctly it handled the best it has ever been with nothing but improvements on the way! (Thanks Elka!)
As it seems to be the case, I was still working on the 700 fabbing a last minute solution for the suspension, got everything bolted together, threw it in the trailer and headed up to Utah from Arizona to finish putting it together there. Turns out I missed a piece which I would pay for later on.
While the rain was coming down, and the lightning flashed and the thunder rolled and hail pelted the trailer….and was that really deep pervasive rumble from the Nevada earthquake? While all that was happening, I jacked up the SxS, in the trailer, so I could bolt on the skid plate. Talk about tight quarters, but it was a mud wash outside so that was not an option. I then went to bolt up the snorkel for the CVT and realized a 90 degree elbow was missing. The air port for the CVT faced directly back right where all the mud from the tires will be kicked up to. So I ended up zip tying a rag over the port to keep the mud out, but still allow for “some” air movement. You can guess where this is leading.

The rain abated to a light drizzle just before my time to head out for the unclassified so I took off and had a good time getting used to the new suspension and the track. After my session I loaded the SxS and the 1000 pounds of mud back into the trailer and went on a search for a car wash. Mud was everywhere, but my rag still held over the CVT inlet and looked to be doing its job, so that was good…or so I thought. After the 700 was looking fresh as a daisy again, it was my turn. Apparently I need more than one driving suit, I found the laundry at the hotel and got the suit cleaned up and did the same for myself as power washers have a way of ejecting mud off of the vehicle and onto you. I am sure the lady behind the counter at the hotel had to wonder if they made the right decision letting me stay there when I went to check in after washing the SxS, reputable would not be a word I would use to describe my appearance.
My race wasn’t until the afternoon so I could sleep in which I really needed after the late nights prepping the 700 for this race. The forecast called for rain and thunderstorms all day, so I resigned myself to the fact it was going to be one of “those” races.

The next day, after a leisurely morning, I get out to the course and it looks relatively dry! The ground is still muddy, but no torrential downpours or constant soaking drizzle, it looks like it might be a fine day for racing! I quickly finish up getting the 700 ready which included installing the fire extinguisher, battening down some of the plastic pieces, installing my number plates and kicking the tires to make sure they have the proper air pressure. As race time approaches the weather is still holding out, though there are some dark air masses obscuring the hills not too far away.
Unlike the previous races, they line up the 700 class with the 600s so the starting line is full, the more the merrier I say. Despite the different displacement, it is all a good match as the smaller vehicles are also lighter weight, so power to weight is fairly even across the board except for my main competition, an Arctic Cat Wildcat sport. It is a 700cc twin with 15 more hp than I have, 12+ inches of travel all around on Elka Stage 5 shocks, 20mph more top speed and a lighter vehicle. Fine, I know when a race is rigged by a sport SxS versus a utility SxS. That’s ok, I’m down for the challenge.

The other lines take off, 38 SxSs total in this race. The flag drops for our line and we’re gone! I end up in 6th place around the first corner and the race is on! I have to say I had a lot of fun this race. The suspension is making all the difference in the world in what I can do, and we still have more to go in that department. As we all make it around the first few corners, I realize that I’m still in the mix, no one is just walking away from me and so the first lap is like that, very close racing, slicing and dicing with the others, this is what it’s all about! Well, the rain decides to start coming towards the end of lap one and I pull at a tear off only to take the whole stack! Gads! That’s ok, just a thing.
There are quite a few rolled over SxS’s on the course, so I’m playing it safe trying not to be a statistic, but with blurred vision from the rain, and a better feel for what I can do, I pick up the pace on lap #2 (blurred vision makes you go faster because you don’t see what you need to slow down for). By the end of lap two (it’s a four lap race, about 55 minutes) I think I have passed all of the 600’s and I have caught up to the Arctic Cat, that’s right, a KYMCO chasing down an Arctic Cat. Ironically, KYMCO builds the Wildcat Sport for Arctic Cat, they are a good builder.  As we start lap #3, I am hanging off the bumper of the Arctic Cat and two wheeling it around corners, as we hit a whoop section, my oversight in packing catches up to me and my CVT belt disintegrates due to the rag slowing down airflow to keep it cool. I roll off the course with all kinds of smoke billowing around me and know my race is done.

The race didn’t end the way I wanted, but the racing exceeded my expectations, all in all, it was a good day. The KYMCO performed excellently against the other SxSs and I know I have more to go before I max out its performance capabilities. Based on my lap times, I would have finished mid pack against this entire race field of 38, 27 of which are 900cc or larger. We’re going in the right direction!

Thanks to my sponsors, all of whom play an important part in my success.
KYMCO – Building quality machines, and yes, they can race. http://www.kymcousa.com/
MSA- Motor Sport Alloys makes great and stylish wheels, making me look good and holding the tires to the SxS at the same time with their M21 Lok beadlock wheels. http://cocomponents.com/dealer/atv-wheels/
EFX Performance Tires – Those MotoHammers are tough tires with a great all terrain tread pattern, mud rocks, sand, it doesn’t matter. http://cocomponents.com/dealer/atv-tires-golfcar-tires/
Elka – Stage 5 shocks, connecting the SxS to the ground in comfort and style over jumps and through the whoops. http://www.elkasuspension.com/

Most important…my Wife. Understanding, patience, tolerance, support…even encouragement. Without her, I couldn’t do what I do.

Thanks!!
Alex Kollitz
WARP Offroad
www.warpoffroad.com

PS. I now have the series points lead for the 700 class!



30
Side By Side / Re: Aftermarket Shocks
« on: May 26, 2015, 03:50:32 AM »
I am writing up my race report right now. If you like the SP, you are going to love my suspension kit. I didn't get the arms done in time for the race, so I am still shy a couple of inches of travel front and back, but the shocks worked great. I was catching air and hitting all types of whoops with only a couple of issues. The really deep whoops will require a bit more travel and I bottomed out the rear on a flat landing on a tabletop....but not by much! All in all very happy with the shocks and can't wait to get them dialed in with the full travel.

Pages: 1 [2] 3 4